How to Make Elastic Seat Covers

If you have old, worn out chairs that you can’t bear to part with but don’t want to look at anymore, make some seat covers! Elastic seat covers are easy and inexpensive to make, and they can give new life to your favorite chair. Plus, they’re a great way to add a pop of color or pattern to any room.

DIY | How to Make Removable CHAIR COVERS

  • Cut four pieces of elastic, each about 22 inches long
  • Fold each piece in half and sew the ends together to create a loop
  • Pin the loops evenly around the perimeter of the seat cover, with the raw edges facing inward
  • Sew around the edge of the seat cover, making sure to catch all four loops of elastic in the seam
  • Trim any excess thread and enjoy your new, stretchy seat covers!

How to Sew a Box Cushion Cover No Zipper

Assuming you have a basic understanding of how to sew, here are the steps to sew a box cushion cover without using a zipper. You will need to gather your materials which include fabric for the top and bottom of the cushion, batting or stuffing, and thread. Once you have your materials, cut the fabric for the top and bottom of the cushion to the desired size leaving about ½ an inch extra for seam allowance.

Next, lay the fabric pieces wrong sides together and sew them together using a straight stitch along all four sides. Now it’s time to stuff your cushion! If you’re using batting, cut it to fit inside the sewn fabric casing snugly.

If you’re using stuffing, fluff it up before placing it inside the casing. Once your cushion is stuffed, hand-sew the opening closed using a blind stitch or ladder stitch. And that’s it!

How to Make Elastic Seat Covers


How Do You Make a Drawstring Cushion Cover?

Making a drawstring cushion cover is actually quite easy! All you need is some fabric, a sewing machine, and a little bit of patience. Here are the steps:

1. Cut two pieces of fabric that are the same size. You can make them whatever size you want, but keep in mind that the finished product will be smaller than the pieces of fabric you start with. 2. Sew the two pieces of fabric together along three sides, leaving one side open.

3. Turn the piece of fabric inside out so that the seams are on the inside. 4. Fold over the open edge about ½ inch and sew it shut. This will create a nice finish and prevent fraying.

5. Thread a length of cord or string through the casing you just created (this is where that one open side comes in handy). Make sure to leave enough slack at either end so that you can tie it shut when needed.

How Do You Make a Seat Cover With Piping?

If you want to add a little extra something-something to your seat covers, piping is a great way to go. It’s not difficult to do, but there are a few things you need to keep in mind. Here’s how to make seat covers with piping:

1. Cut your fabric. You’ll need two pieces of fabric for each seat cover, plus an extra inch or two all the way around for seam allowance. When cutting, be sure to leave enough room for the piping cord.

2. Make the piping. To make your own piping, simply wrap bias tape around cording until it’s fully covered. You can buy bias tape or make your own (it’s really easy!).

3. Sew the piping onto one of the fabric pieces. Start at one corner and sew along the edge of the bias tape, making sure to catch both sides so that the cording is fully encased. Continue sewing until you reach the end of the fabric piece.


How Do You Make a Removable Bench Cushion Cover?

If you have a bench with a removable cushion, you can easily make a cover for it. All you need is some fabric and a few supplies. Here’s how to do it:

1. Measure the cushion to determine how much fabric you’ll need. Add several inches to account for seams and hems. 2. Cut the fabric to size, using sharp scissors or a rotary cutter.

3. Hem the sides and bottom of the fabric, using either a sewing machine or hand stitching. 4. Install grommets along one side of the top hem, if desired (this will make it easier to put the cover on and take it off). Alternatively, you can use ties or Velcro to secure the cover in place.

5. Put the cover on your bench cushion and enjoy!

How Do You Make a Bar Stool Seat Cover?

A bar stool seat cover is a great way to add style and comfort to your bar stools. There are a few things you need to know before you start shopping for a seat cover. First, measure the diameter of the seat and the height of the backrest.

Second, decide what kind of fabric you want to use. Third, choose a color or pattern that will complement your décor. Once you have all of this information, you can start shopping for a bar stool seat cover.

There are many different styles and colors available, so take your time and find one that fits your needs. If you’re not sure how to install the seat cover, most stores will be happy to help you out or provide instructions.


Making your own elastic seat covers is a great way to personalize your car or truck. You can choose from a variety of colors and patterns to match your personality and style. Plus, making them yourself is easy and only takes a few minutes!

Here’s what you’ll need: -1 yard of fabric (quilting cotton works well) -1/4 inch wide elastic

-Scissors -Sewing machine First, cut your fabric into two rectangles that are 18 inches wide by 22 inches long.

Then, fold over one long side of each rectangle 1/4 inch and press with an iron. Next, fold over again 1/2 inch and press again. Sew along the folded edge with a straight stitch to create a seam.

Repeat this step for the other long side and both short sides of the fabric rectangles. Now it’s time to attach the elastic. On one short side of each rectangle, sew along the top edge with a basting stitch, leaving about 3 inches unsewn in the middle.

Backstitch at the beginning and end of this section so that your stitches don’t come undone later. Cut two pieces of elastic that are 10 inches long each, then use a safety pin to thread one through each casing you just created. Sew along the open edge with a straight stitch to close up the casing, being sure to catch both ends of the elastic inside so that they don’t get pulled out when you’re using your seat covers.

Trim any excess thread and enjoy!